Last updated: April 23, 2026
AC installation across San Diego County runs $6,800 to $16,000 for a complete system, installed, after a free in-home estimate. A standard single-stage system on a typical home lands toward the lower end. Variable-speed equipment, a heat pump conversion, or a home that needs duct work or a panel upgrade push it higher. Pricing is the same everywhere in the county, with no travel surcharge.
Palomar Mountain sits at 5,500 feet with genuine alpine winters, substantial snowfall included, and mild summers, which means cold-climate heating performance is the priority here rather than cooling capacity. Cabin and small-residential stock is the norm, anchored by the Palomar Observatory community. Permits route through the County of San Diego, and severe SDG&E power shutoff exposure combined with real winter isolation makes battery backup particularly valuable for keeping heat running through storm-related outages.
Mountain installs often mean dual-fuel configurations, a heat pump plus gas or propane backup, and longer line-set runs on larger rural lots, both of which add real material and labor cost. Add the drive time from the nearest service hub and this zone runs the highest install range in the county.
| Item | Typical cost | Notes |
|---|---|---|
| In-home installation estimate | Free | A measured quote in your home, not a phone guess |
| Manual J load calculation | Included | Part of every estimate, sizes the system to your actual home |
| Standard central AC system, installed | $7,000 - $10,000 | 14.3 SEER2 single-stage, the most common install countywide |
| Two-stage system, installed | $9,500 - $12,500 | Runs at low capacity most of the time, better humidity control |
| Variable-speed high-efficiency system, installed | $11,000 - $14,000 | Best comfort and efficiency, the highest equipment tier |
| Heat pump conversion, installed | $9,500 - $15,000 | Replaces AC and furnace with one system, qualifies for the largest rebates |
| Coastal-rated condenser upgrade | $400 - $1,200 added | Corrosion-resistant coil and hardware for homes near the water |
| Refrigerant line set replacement | $800 - $1,800 | When the existing line set can’t be safely reused |
| Mechanical permit | $250 - $500 | Pulled by us, inspection scheduled and included |
| Duct sealing or partial duct replacement | $1,000 - $4,000 | Quoted only if the duct inspection finds real air loss |
| Older-home electrical panel upgrade | $2,500 - $5,500 | Common on homes built before the 1980s |
Ranges reflect Palomar Mountain and Backcountry San Diego. Your exact figure depends on the factors below. We quote flat-rate before starting.
SDG&E and TECH Clean California rebates apply to qualifying equipment, and they're largest for heat pump installs. The federal 25C tax credit can stack on top for equipment that qualifies. Exact rebate amounts depend on your home and the equipment you choose, so we confirm what you actually qualify for during the estimate rather than quoting a number up front. We also offer financing so a full replacement doesn't have to come out of savings all at once.
Yes. At 5,500 feet with substantial annual snowfall, a standard mild-climate heat pump loses too much heating capacity in genuine alpine cold to keep a cabin comfortable through winter. We spec cold-climate-rated equipment built to maintain output well below freezing, and given how isolated Palomar Mountain gets during winter storms, battery backup is worth serious consideration alongside the heat pump itself.
Mountain installs often mean dual-fuel configurations, a heat pump plus gas or propane backup, and longer line-set runs on larger rural lots, both of which add real material and labor cost. Add the drive time from the nearest service hub and this zone runs the highest install range in the county.
A complete system runs $6,800 to $16,000 installed, with most single-family homes landing in the $7,000 to $12,000 range. The free in-home estimate breaks out equipment, labor, and permit costs before you decide.
For most San Diego homes, yes, especially near the coast where humidity is higher. It runs quieter, holds a steadier temperature, and uses less electricity over a full season. On a smaller inland home with simple cooling needs, a standard single-stage system is often the more practical choice.
The in-home estimate and the Manual J load calculation are both free and included in every quote. On the installed system itself, a standard single-stage unit is the lowest-cost option that still comes with a full manufacturer warranty.
Yes. SDG&E and TECH Clean California both offer rebates, and they're largest for heat pump systems. The federal 25C tax credit can stack on top for qualifying equipment. We confirm exact eligibility and dollar amounts during your estimate rather than promising a number in advance.
Flat-rate pricing, confirmed before any work starts. Same-day scheduling on most calls.