Last updated: April 23, 2026
Furnace repair in San Diego County typically runs $200 to $900, starting with an $89 diagnostic that gets credited toward the fix. Ignitor and flame sensor problems make up most of the cheap end. A cracked heat exchanger is the one repair that usually means it's time to talk about replacement instead.
Kearny Mesa is almost entirely commercial-industrial HVAC work, Convoy District restaurant kitchen ventilation, warehouse rooftop package units, and dealership systems along the auto row make up the call mix rather than residential replacements. Pricing runs by tonnage, ventilation-balancing complexity for kitchen exhaust and makeup-air work, and access. Permits route through the City of San Diego, with commercial kitchen work often requiring additional health department coordination.
Central San Diego furnaces are often original equipment in older homes, so the repair-vs-replace line gets crossed more often here. When a repair still makes sense, ignition failures and cracked flame sensors are the usual ticket, priced at the county standard.
| Item | Typical cost | Notes |
|---|---|---|
| $89 diagnostic visit | $89 | Credited toward the repair once you approve the work |
| Hot-surface ignitor replacement | $250 - $500 | The most common reason a furnace won’t light |
| Flame sensor cleaning or replacement | $150 - $350 | Causes the furnace to shut off seconds after igniting |
| Inducer motor replacement | $400 - $800 | Furnace hums or clicks but won’t start the burner cycle |
| Gas valve replacement | $400 - $900 | Safety component, always tested before replacement is approved |
| Control board replacement | $400 - $800 | More common on furnaces with electronic ignition and diagnostics |
| Blower motor replacement | $450 - $900 | Furnace heats but airflow through the vents is weak or silent |
| Heat exchanger replacement | $1,500 - $3,500 | A safety-critical repair, often the point to consider a new furnace instead |
Ranges reflect Kearny Mesa and Central San Diego. Your exact figure depends on the factors below. We quote flat-rate before starting.
A furnace repair under roughly $500 on a unit less than 12 years old is almost always the right call. A cracked heat exchanger is different. It's a safety issue, not just a repair line item, because a cracked exchanger can leak combustion gases into the home. On a furnace old enough to need one, we usually recommend replacement over repair, and we explain exactly why before you spend money either way.
The $89 diagnostic gets credited toward the repair once you approve it. SDG&E and TECH Clean California rebates apply to new equipment, not repairs, so they come into play only if a repair turns into a replacement conversation, most often after a heat exchanger fails. We offer financing for larger repairs, and we'll tell you plainly when a repair isn't worth it anymore.
Makeup-air balancing is usually the bigger cost factor, not the exhaust hood itself. Getting kitchen exhaust and makeup air properly balanced for a Convoy District restaurant space often requires coordinating with the building's existing rooftop package unit and sometimes adding dedicated makeup-air equipment, which can run several thousand dollars depending on kitchen size and existing infrastructure.
Central San Diego furnaces are often original equipment in older homes, so the repair-vs-replace line gets crossed more often here. When a repair still makes sense, ignition failures and cracked flame sensors are the usual ticket, priced at the county standard.
$200 to $900 covers most repairs, including the $89 diagnostic that gets credited toward the fix. Ignitor and flame sensor issues run under $500. A gas valve, control board, or blower motor runs $400 to $900.
Usually yes if the repair is under $500 and the furnace is less than 12 years old. A cracked heat exchanger is the exception. That's a safety issue, and on an older furnace we typically recommend replacement instead.
A flame sensor cleaning or replacement is usually the least expensive fix, typically $150 to $350, and it's one of the most common reasons a furnace shuts off right after lighting.
A heat exchanger replacement runs $1,500 to $3,500 and is the most expensive single repair. Because of the safety issue involved and the age of furnaces that usually need one, we walk through the full replacement cost alongside it.
Flat-rate pricing, confirmed before any work starts. Same-day scheduling on most calls.