Furnace repair in San Diego County typically runs $200 to $900, starting with an $89 diagnostic that gets credited toward the fix. Ignitor and flame sensor problems make up most of the cheap end. A cracked heat exchanger is the one repair that usually means it's time to talk about replacement instead.
Typical range in Mission Valley (Central)$200 to $900Flat-rate quote confirmed before any work. No travel surcharge to Mission Valley.
What drives furnace repair cost in Mission Valley?
Mission Valley's HVAC cost picture is dominated by commercial work, Fashion Valley, Westfield, and the Hotel Circle corridor drive rooftop package unit replacement, restaurant kitchen makeup-air systems, and multi-family central plant service rather than typical single-family residential jobs. Pricing here runs by tonnage, access difficulty, and whether work can happen during business hours or needs after-hours scheduling. Permits route through the City of San Diego.
Central San Diego furnaces are often original equipment in older homes, so the repair-vs-replace line gets crossed more often here. When a repair still makes sense, ignition failures and cracked flame sensors are the usual ticket, priced at the county standard.
What goes into a furnace repair bill
Item
Typical cost
Notes
$89 diagnostic visit
$89
Credited toward the repair once you approve the work
Hot-surface ignitor replacement
$250 - $500
The most common reason a furnace won’t light
Flame sensor cleaning or replacement
$150 - $350
Causes the furnace to shut off seconds after igniting
Inducer motor replacement
$400 - $800
Furnace hums or clicks but won’t start the burner cycle
Gas valve replacement
$400 - $900
Safety component, always tested before replacement is approved
Control board replacement
$400 - $800
More common on furnaces with electronic ignition and diagnostics
Blower motor replacement
$450 - $900
Furnace heats but airflow through the vents is weak or silent
Heat exchanger replacement
$1,500 - $3,500
A safety-critical repair, often the point to consider a new furnace instead
Ranges reflect Mission Valley and Central San Diego. Your exact figure
depends on the factors below. We quote flat-rate before starting.
What moves the price up or down
Furnace age and whether it's still under manufacturer parts warranty
Whether the failure is electrical (board, ignitor) or mechanical (inducer, blower)
Brand and part availability, since some control boards are special-order
Access. A furnace in a tight attic or garage closet takes longer to service than one in an open utility room
Heat exchanger condition, which is a safety issue and not just a comfort one
Whether the system needs a single repair or several components have failed together
Repair or replace?
A furnace repair under roughly $500 on a unit less than 12 years old is almost always the right call. A cracked heat exchanger is different. It's a safety issue, not just a repair line item, because a cracked exchanger can leak combustion gases into the home. On a furnace old enough to need one, we usually recommend replacement over repair, and we explain exactly why before you spend money either way.
Rebates and ways to save in Mission Valley
The $89 diagnostic gets credited toward the repair once you approve it. SDG&E and TECH Clean California rebates apply to new equipment, not repairs, so they come into play only if a repair turns into a replacement conversation, most often after a heat exchanger fails. We offer financing for larger repairs, and we'll tell you plainly when a repair isn't worth it anymore.
Furnace repair cost questions, answered for Mission Valley
Why does commercial HVAC work in Mission Valley often cost more per ton than residential?
Access and scheduling mostly. Rooftop package units on retail and hotel buildings often need lift access, and most Mission Valley commercial clients require after-hours or overnight scheduling so business operations aren't disrupted, which adds a labor premium over daytime residential work. Kitchen makeup-air system integration for restaurant tenants also adds ventilation-balancing scope that residential jobs don't have.
Why does furnace repair cost what it does in Central San Diego?
Central San Diego furnaces are often original equipment in older homes, so the repair-vs-replace line gets crossed more often here. When a repair still makes sense, ignition failures and cracked flame sensors are the usual ticket, priced at the county standard.
How much does furnace repair cost in San Diego?
$200 to $900 covers most repairs, including the $89 diagnostic that gets credited toward the fix. Ignitor and flame sensor issues run under $500. A gas valve, control board, or blower motor runs $400 to $900.
Is it worth repairing an old furnace?
Usually yes if the repair is under $500 and the furnace is less than 12 years old. A cracked heat exchanger is the exception. That's a safety issue, and on an older furnace we typically recommend replacement instead.
What is the cheapest furnace repair?
A flame sensor cleaning or replacement is usually the least expensive fix, typically $150 to $350, and it's one of the most common reasons a furnace shuts off right after lighting.
What is the most expensive furnace repair?
A heat exchanger replacement runs $1,500 to $3,500 and is the most expensive single repair. Because of the safety issue involved and the age of furnaces that usually need one, we walk through the full replacement cost alongside it.
Serving Mission Valley
Get a real furnace repair quote for Mission Valley
Flat-rate pricing, confirmed before any work starts. Same-day scheduling on most calls.